15 tips on How to 200-101 Test Like a Badass [1 to 15]

★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions

Free Instant Download NEW 200-101 Exam Dumps (PDF & VCE):
Available on: https://www.certleader.com/200-101-dumps.html


Free of 200-101 test preparation materials and preparation labs for Cisco certification for IT specialist, Real Success Guaranteed with Updated 200-101 pdf dumps vce Materials. 100% PASS Interconnecting Cisco Networking Devices Part 2 (ICND2) exam Today!

2016 Apr 200-101 Study Guide Questions:

Q1. Refer to the exhibit. **Exhibit Missing**

A technician pastes the configurations in the exhibit into the two new routers shown. Otherwise, the routers are configured with their default configurations. A ping from Host1 to Host2 fails, but the technician is able to ping the S0/0 interface of R2 from Host1. The configurations of the hosts have been verified as correct. What is the cause of the problem? 

A. The serial cable on R1 needs to be replaced. 

B. The interfaces on R2 are not configured properly. 

C. R1 has no route to the 192.168.1.128 network. 

D. The IP addressing scheme has overlapping subnetworks. 

E. The ip subnet-zero command must be configured on both routers. 

Answer: C 


Q2. Refer to the exhibit. 


Based on the exhibited routing table, how will packets from a host within the 192.168.10.192/26 LAN be forwarded to 192.168.10.1? 

A. The router will forward packets from R3 to R2 to R1. 

B. The router will forward packets from R3 to R1 to R2. 

C. The router will forward packets from R3 to R2 to R1 AND from R3 to R1. 

D. The router will forward packets from R3 to R1. 

Answer: C 


Q3. Which three of these statements regarding 802.1Q trunking are correct? (Choose three.) 

A. 802.1Q native VLAN frames are untagged by default. 

B. 802.1Q trunking ports can also be secure ports. 

C. 802.1Q trunks can use 10 Mb/s Ethernet interfaces. 

D. 802.1Q trunks require full-duplex, point-to-point connectivity. 

E. 802.1Q trunks should have native VLANs that are the same at both ends. 

Answer: ACE 


Q4. Which statement is true, as relates to classful or classless routing? 

A. Classful routing protocols send the subnet mask in routing updates. 

B. RIPv1 and OSPF are classless routing protocols. 

C. Automatic summarization at classful boundaries can cause problems on discontiguous subnets. 

D. EIGRP and OSPF are classful routing protocols and summarize routes by default. 

Answer: C 


Q5. Which two statistics appear in show frame-relay map output? (Choose two.) 

A. the number of BECN packets that are received by the router 

B. the value of the local DLCI 

C. the number of FECN packets that are received by the router 

D. the status of the PVC that is configured on the router 

E. the IP address of the local router 

Answer: BD 


200-101 latest exam

Up to date 200-101 free question:

Q6. Refer to the exhibit. 


RTA is configured with a basic configuration. The link between the two routers is operational and no routing protocols are configured on either router. The line shown in the exhibit is then added to router RTA. Should interface Fa0/0 on router RTB shut down, what effect will the shutdown have on router RTA? 

A. A route to 172.16.14.0/24 will remain in the RTA routing table. 

B. A packet to host 172.16.14.225 will be dropped by router RTA. 

C. Router RTA will send an ICMP packet to attempt to verify the route. 

D. Because router RTB will send a poison reverse packet to router RTA, RTA will remove the route. 

Answer: A 


Q7. DRAG DROP 


Answer: 



Q8. What is the purpose of Inverse ARP? 

A. to map a known IP address to a MAC address 

B. to map a known DLCI to a MAC address 

C. to map a known MAC address to an IP address 

D. to map a known DLCI to an IP address 

E. to map a known IP address to a SPID 

F. to map a known SPID to a MAC address 

Answer: D 


Q9. Which three statements are typical characteristics of VLAN arrangements? (Choose three.) 

A. A new switch has no VLANs configured. 

B. Connectivity between VLANs requires a Layer 3 device. 

C. VLANs typically decrease the number of collision domains. 

D. Each VLAN uses a separate address space. 

E. A switch maintains a separate bridging table for each VLAN. 

F. VLANs cannot span multiple switches. 

Answer: BDE 


Q10. Which command is used to enable CHAP authentication, with PAP as the fallback method, on a serial interface? 

A. Router(config-if)# ppp authentication chap fallback ppp 

B. Router(config-if)# ppp authentication chap pap 

C. Router(config-if)# authentication ppp chap fallback ppp 

D. Router(config-if)# authentication ppp chap pap 

Answer: B 


200-101 simulations

Verified 200-101 item pool:

Q11. What is the result of issuing the frame-relay map ip 192.168.1.2 202 broadcast command? 

A. defines the destination IP address that is used in all broadcast packets on DCLI 202 

B. defines the source IP address that is used in all broadcast packets on DCLI 202 

C. defines the DLCI on which packets from the 192.168.1.2 IP address are received 

D. defines the DLCI that is used for all packets that are sent to the 192.168.1.2 IP address 

Answer: D 


Q12. Refer to the exhibit. 


The Lakeside Company has the internetwork in the exhibit. The administrator would like to reduce the size of the routing table on the Central router. Which partial routing table entry in the Central router represents a route summary that represents the LANs in Phoenix but no additional subnets? 

A. 10.0.0.0/22 is subnetted, 1 subnets D 10.0.0.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1 

B. 10.0.0.0/28 is subnetted, 1 subnets D 10.2.0.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1 

C. 10.0.0.0/30 is subnetted, 1 subnets D 10.2.2.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1 

D. 10.0.0.0/22 is subnetted, 1 subnets D 10.4.0.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1 

E. 10.0.0.0/28 is subnetted, 1 subnets D 10.4.4.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1 

F. 10.0.0.0/30 is subnetted, 1 subnets D 10.4.4.4 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1 

Answer: D 


Q13. Which two statements describe the process identifier that is used in the command to configure OSPF on a router? (Choose two.) 

Router(config)# router ospf 1 

A. All OSPF routers in an area must have the same process ID. 

B. Only one process number can be used on the same router. 

C. Different process identifiers can be used to run multiple OSPF processes 

D. The process number can be any number from 1 to 65,535. 

E. Hello packets are sent to each neighbor to determine the processor identifier. 

Answer: CD 


Q14. To allow or prevent load balancing to network 172.16.3.0/24, which of the following commands could be used in R2? (Choose two.) 



A. R2(config-if)#clock rate 

B. R2(config-if)#bandwidth 

C. R2(config-if)#ip ospf cost 

D. R2(config-if)#ip ospf priority 

E. R2(config-router)#distance ospf 

Answer: BC 


Q15. Refer to the exhibit. 


Assuming that the entire network topology is shown, what is the operational status of the interfaces of R2 as indicated by the command output shown? 

A. One interface has a problem. 

B. Two interfaces have problems. 

C. The interfaces are functioning correctly. 

D. The operational status of the interfaces cannot be determined from the output shown. 

Answer: C