Most up-to-date 200-125: Actualtests real testing engine from 21 to 30


♥♥ 2018 NEW RECOMMEND ♥♥

Free VCE & PDF File for Cisco 200-125 Real Exam (Full Version!)

★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions

Free Instant Download NEW 200-125 Exam Dumps (PDF & VCE):
Available on: https://www.certleader.com/200-125-dumps.html


Most of the particular training materials are available in the structure of Pdf questions and also answers. You can download the particular exam engine software on your PC and practice the particular simulated tests according to your own need. Just click the mouse and also confirm your payment today. All the Cisco Cisco exam braindumps can presented for you. And you will have a chance to be able to enjoy the particular free updated 200-125 components within 120 days after paying. You are guaranteed to create success together with our Cisco 200-125 exam goods. Otherwise, you are going to get the entire money back again of paying costs.

2017 Mar 200-125 torrent

Q21.  - (Topic 8)

What is one requirement for interfaces to run IPv6?

A. An IPv6 address must be configured on the interface.

B. An IPv4 address must be configured.

C. Stateless autoconfiguration must be enabled after enabling IPv6 on the interface.

D. IPv6 must be enabled with the ipv6 enable command in global configuration mode.

Answer: A

Explanation: To use IPv6 on your router, you must, at a minimum, enable the protocol and assign IPv6 addresses to your interfaces.


Q22.  - (Topic 8)

Which RFC was created to alleviate the depletion of IPv4 public addresses?

A. RFC 4193

B. RFC 1519

C. RFC 1518

D. RFC 1918

Answer: C


Q23.  - (Topic 5)

On which options are standard access lists based?

A. destination address and wildcard mask

B. destination address and subnet mask

C. source address and subnet mask

D. source address and wildcard mask

Answer: D

Explanation:

Standard ACL’s only examine the source IP address/mask to determine if a match is made. Extended ACL’s examine the source and destination address, as well as port information.


Q24.  - (Topic 3)

Refer to the exhibit.

For what two reasons has the router loaded its IOS image from the location that is shown? (Choose two.)

A. Router1 has specific boot system commands that instruct it to load IOS from a TFTP server.

B. Router1 is acting as a TFTP server for other routers.

C. Router1 cannot locate a valid IOS image in flash memory.

D. Router1 defaulted to ROMMON mode and loaded the IOS image from a TFTP server.

E. Cisco routers will first attempt to load an image from TFTP for management purposes.

Answer: A,C

Explanation:

The loading sequence of CISCO IOS is as follows: Booting up the router and locating the Cisco IOS

1. POST (power on self-test)

2. Bootstrap code executed

3. Check Configuration Register value (NVRAM) which can be modified using the config- register command

0 = ROM Monitor mode 1 = ROM IOS

2 - 15 = startup-config in NVRAM

4. Startup-config filE. Check for boot system commands (NVRAM)

If boot system commands in startup-config

a. Run boot system commands in order they appear in startup-config to locate the IOS

b. [If boot system commands fail, use default fallback sequence to locate the IOS (Flash, TFTP, ROM)?]

If no boot system commands in startup-config use the default fallback sequence in locating the IOS:

a. Flash (sequential)

b. TFTP server (netboot)

c. ROM (partial IOS) or keep retrying TFTP depending upon router model

5. If IOS is loaded, but there is no startup-config file, the router will use the default fallback sequence for locating the IOS and then it will enter setup mode or the setup dialogue.


Q25. CORRECT TEXT - (Topic 6)

A network associate is adding security to the configuration of the Corp1 router. The user on host C should be able to use a web browser to access financial information from the Finance Web Server. No other hosts from the LAN nor the Core should be able to use a web browser to access this server. Since there are multiple resources for the corporation at this location including other resources on the Finance Web Server, all other traffic should be allowed.

The task is to create and apply an access-list with no more than three statements that will allow ONLY host C web access to the Finance Web Server. No other hosts will have web access to the Finance Web Server. All other traffic is permitted.

Access to the router CLI can be gained by clicking on the appropriate host. All passwords have been temporarily set to "cisco".

The Core connection uses an IP address of 198.18.196.65.

The computers in the Hosts LAN have been assigned addresses of 192.168.33.1 - 192.168.33.254

✑ host A 192.168.33.1

✑ host B 192.168.33.2

✑ host C 192.168.33.3

✑ host D 192.168.33.4

The servers in the Server LAN have been assigned addresses of 172.22.242.17 - 172.22.242.30.

The Finance Web Server is assigned an IP address of 172.22.242.23.

Answer: 

Select the console on Corp1 router Configuring ACL

Corp1>enable Corp1#configure terminal

comment: To permit only Host C (192.168.33.3){source addr} to access finance server address (172.22.242.23) {destination addr} on port number 80 (web) Corp1(config)#access-list 100 permit tcp host 192.168.33.3 host 172.22.242.23 eq 80 comment: To deny any source to access finance server address (172.22.242.23)

{destination addr} on port number 80 (web)

Corp1(config)#access-list 100 deny tcp any host 172.22.242.23 eq 80

comment: To permit ip protocol from any source to access any destination because of the implicit deny any any statement at the end of ACL.

Corp1(config)#access-list 100 permit ip any any Applying the ACL on the Interface

comment: Check show ip interface brief command to identify the interface type and number by checking the IP address configured.

Corp1(config)#interface fa 0/1

If the ip address configured already is incorrect as well as the subnet mask. This should be corrected in order ACL to work

type this commands at interface mode :

no ip address 192.x.x.x 255.x.x.x (removes incorrect configured ipaddress and subnet mask)

Configure Correct IP Address and subnet mask:

ip address 172.22.242.30 255.255.255.240 ( range of address specified going to server is given as 172.22.242.17 - 172.22.242.30 )

Comment: Place the ACL to check for packets going outside the interface towards the

finance web server.

Corp1(config-if)#ip access-group 100 out Corp1(config-if)#end

Important: To save your running config to startup before exit. Corp1#copy running-config startup-config

Verifying the Configuration:

Step1: show ip interface brief command identifies the interface on which to apply access list.

Step2: Click on each host A, B, C, & D. Host opens a web browser page, Select address box of the web browser and type the ip address of finance web server (172.22.242.23) to test whether it permits /deny access to the finance web Server.

Step 3: Only Host C (192.168.33.3) has access to the server. If the other host can also access then maybe something went wrong in your configuration. Check whether you configured correctly and in order.

Step 4: If only Host C (192.168.33.3) can access the Finance Web Server you can click on NEXT button to successfully submit the ACL SIM.


Up to date 200-125 practice exam:

Q26.  - (Topic 8)

when you troubleshoot an IPv4 connectivity issue on a router, which three router configuration checks you must perform?

A. Verify that the router interface IP address IP address is correct.

B. Verify that the DNS is configured correctly.

C. Verify that the router and the host use the same subnet mask.

D. Verify that the router firmware is up-to-date.

E. Verify that a default route is configured.

F. Verify that the route appears in the routing table

Answer: A,B,F


Q27.  - (Topic 8)

Refer to the exhibit.

You have discovered that computers on the 192 168 10 0/24 network can ping their default gateway, but they cannot connect to any resources on a remote network Which reason for the problem is most likely true?

A. The 192.168.12 0/24 network is missing from OSPF

B. The OSPF process ID is incorrect

C. The OSPF area number is incorrect.

D. An ARP table entry is missing for 192.168.10.0.

E. A VLAN number is incorrect for 192.168.10.0.

Answer: C


Q28.  - (Topic 8)

Which Cisco platform can verify ACLs?

A. Cisco Prime Infrastructure

B. Cisco Wireless LAN Controller

C. Cisco APIC-EM

D. Cisco IOS-XE

Answer: B


Q29.  - (Topic 8)

Which statement about LLDP is true?

A. It is a Cisco proprietary protocol.

B. It is configured in global configuration mode.

C. The LLDP update frequency is a fixed value.

D. It runs over the transport layer.

Answer: B


Q30.  - (Topic 8)

Why did Branch1 router lose WAN connectivity with R1 router?

A. The IP address is misconfigured on PPP multilink interface on the Branch1 router.

B. The PPP multilink group is misconfigured on the £ranch1 serial interfaces.

C. The PPP multilink group is misconfigured on the R1 serial interfaces.

D. The Branch1 serial interfaces are placed in a shutdown condition.

Answer: A



see more CCNA Cisco Certified Network Associate CCNA (v3.0)